Bosch Router Table

Ideal for cutting in tight spaces where other saws can't reach, the XPR MultiSaw makes cutting scroll and straight-line patterns a cinch. The attachment features a universal blade holder that accepts both -InchU-Inch and -InchT-Inch shank blades for maximum versatility. Your purchase is covered by a 5-year warranty.

Amazon Sales Rank: #67839 in Home Improvement Brand: Dremel Model: MS400 Dimensions: .0" h x .0" w x .0" l, Universal blade holder for optimal versatility Uses U and T shank blades for a variety of applications Features 3/8-inch blade stroke for fast and controllable cutting Cuts materials up to 1-1/2-inch thick with supplied blade for cutting applications large and small 5-year warranty for increased reliability

Ideal for cutting in tight spaces where other saws can't reach, the XPR MultiSaw makes cutting scroll and straight-line patterns a cinch. The attachment features a universal blade holder that accepts both "U" and "T" shank blades for maximum versatility. Your purchase is covered by a 5-year warranty. FEATURES Universal blade holder for optimal versatility Uses "U" & "T" shank blades for a variety of applications 3/8-inch blade stroke for fast and controllable cutting Cuts materials up to 1-1/2-inch thick with supplied blade for cutting applications large and small 5-year warranty for excellent reliability What's in the Box MultiSaw Attachment SPECIFICATIONS Blade stroke: 3/8 inches

Most helpful customer reviews 35 of 37 people found the following review helpful. This thing saved me some big money. By ztiger This attachment came with my 400 XPR. My first impression, when I saw it and put it on the XPR, was that this thing is going to be a pain to control. But one incident completely changed my mind. I have a house that was built in the 50's and the doors and the door knobs are all from the time that the house was built. A few of the inside door knobs quit working properly so I went and got some new knobs. The standard door knobs now have different depths and diameters than the originals on my doors. I had my choice; buy all new doors and knobs or break out this Dremel MultiSaw attachment and go crazy. Man does this thing work great!!! It got around in those doors like a hot knife through melted butter. It uses blades for most standard jigsaws, so I had other blades around. This thing saved me the cost of buying all new doors for my house. I recut three dorr knob holes and the latch holes in a matter of 20 minutes and installed the new knobs in 10 more. If you don't have this for your XPR, get it!! 36 of 39 people found the following review helpful. For 400 XPR, 4000, and 8200 Rotary Tool ONLY By C. MacPhail Nothing in the Amazon listing warned me of this. The box and front of the owner manual say "For use with Dremel 400 Series XPR." Page 5 of the manual says "For use with Dremel 400 Series XPR Rotary tool only." (Subsequent models 4000 and 8200 are also compatible.) Reviewer "Osama I. J. Deir" says it works with his Dremel 395 series tool, and I was able to attach and run it with mine. But 2 gray plastic tabs at the saw's connection point prevent it from seating well. Ironically, you could use your Dremel to grind off the tabs and get a better connection to your non-XPR Dremel tool. But I am returning my MultiSaw because Dremel is telling me in multiple ways that it's not a good idea. Maybe it's overload issue...who knows? Nice that Amazon returns are super easy. 16 of 16 people found the following review helpful. Don't expect too much. By AWBoater I was very disappointed in this tool. I bought it to cut out a 12" x 6" panel in 1/4" thick fiberglass with 1/16" aluminum on one surface. Since it used standard jig saw blades, I figured it would be up to the task. The primary reason I used this item rather than a jig saw is that I had a restricted area where the jig saw would not fit. It made it about half way through the job when it quit working. When I disassembled it, I found it had nylon (or perhaps simply plastic) gears, which were rounded smooth. The manual does caution against running the tool too fast, and I did heed that, but its supposed to be able to cut through 1 1/2" material, so I figured it should have worked for my application. But at any rate, for almost $30, it should have metal gears. Unless you are cutting thin or soft material, get something heftier, like a pneumatic saw. See all 22 customer reviews...

There's nothing like an overarm router for production woodworking. With your ship made templates, this workhorse will crank out consistently accurate wooden parts. In fact, it's built for production work in mind with its foot operated pneumatic spindle control, brake lever, multiple depth stop settings and massive construction. Other features include a heavy tilting table, extra deep throat capacity and large table surface for just about any job you can throw at it. FEATURES: Dovetailed table ways with adjustable gibs, Two-speed control (3-phase model only), Six interchangeable pin sizes, Six adjustable depth stop settings, Large handwheel for smooth operation, Convenient hand brake for fast cycle times, Removable cast iron fence for in-line routing, built-in pressure regulator and lubricator, Adjustable air nozzle, Includes adjustment wrenches, 1/4" and 1/2" collets, 3/8" straight carbide tipped router bit and tool box SPECIFICATIONS: Throat clearance: 25 19/32", Table dimensions: 30" x 23 5/8", Floor to table distance: 36 7/8", Spindle stroke: 3 15/16", Table travel: 8", Hydraulic cylinder: 1 3/16", Clearance between table & chuck: 12", Tilting table: 45 DEG, Spindle speeds: 10,000/20,000 RPM (3-phase), 15,000 RPM (single-phase), Motor: 2 speed 5 HP, 3-phase or 1 speed single-phase, Overall dimensions: 43 5/16" x 31 1/2" x 63", Approximate shipping weight: 909 lbs.

Brand: Grizzly Convenient hand brake for fast cycle times Dovetailed table ways with adjustable gibs Includes adjustment wrenches, 1/4" and 1/2" collets, 3/8" straight carbide tipped router bit and tool box Six adjustable depth stop settings Six interchangeable pin sizes

The Bench Dog 40-002 is a 4.2-Inch ProLift Router Motor.  This 4.20-inch to 3.50-inch motor adapter for the ProLift Ni router adjustment system enables round router motors that are 3.50-inch in diameter to be used with ProLift Ni. The adapter is compatible with Porter Cable 690 series, Bosch 1617/18 series, DeWalt 610, and other products. Features: Enables round router motors that are 3.5 inches in diameter to be used with ProLift Ni router lift Compatible with Bosch 1617/18 series, DeWalt 610, and others 4.2- to 3.5-inch range Professional grade What's In the Box: Bench Dog 40-002 4.2-Inch ProLift Router Motor

Amazon Sales Rank: #111515 in Home Improvement Brand: Bench Dog Model: 40-002 Enables round router motors that are 3.5 inches in diameter to be used with ProLift Ni router lift Compatible with Bosch 1617/18 series, DeWalt 610, and others 4.2- to 3.5-inch range Professional grade 2-year limited warranty

This 4.2-inch to 3.50-inch motor adapter for the ProLift Ni router adjustment system enables round router motors that are 3.50-inch in diameter to be used with ProLift Ni. The adapter is compatible with Porter Cable 690 series, Bosch 1617/18 series, DeWalt 610, and other products.

Most helpful customer reviews 3 of 3 people found the following review helpful. Works Great for Bosch Router By CastAway Bought this to install my Bosch router in the Bench Dog lift table, and it works great. It holds the router steady as a rock. But, it is hard to get the pieces to slide in and out of the table housing when I'm removing or reinstalling the router body; haven't figured out an easy way to do it, yet. 2 of 2 people found the following review helpful. Works as it says By Dr..J You will need this to make your router fit the Bench Dog table. It works as promised 0 of 0 people found the following review helpful. works By Ken B This works as adveritised. Holds my Portercable 690 just fine. Kinda a pain to install considering the 2 halves and motor need to be slid into the router lift. But it works just fine. See all 3 customer reviews...

The FL200 is a pair of Feather-Loc featherboards without the slot adapter. Buy this if you are using the featherboards on equipment with a 1/4 hex t-track.

Amazon Sales Rank: #3458 in Home Improvement Brand: Bench Dog Model: 40-011 Dimensions: 1.00 pounds Two multipurpose featherboards for holding the stock against the guide fence Easy set-up feature; reduces kickback, binding, lifting, and bent blades High tech polymer ensures it will maintain its original shape Advanced design means no marring to your workpiece Designed for 1/4" T-tracks only. Requires Benchdog 10-012 miter slot adapter for miter slots on routers, shapers, band saws, and table saws.

A featherboard is undoubtedly the most underrated router-table accessory of all time. When properly installed, its flexible fingers keep the workpiece pressed tightly against the router tabletop or router fence throughout the routing operation. The result is a dramatic increase in the accuracy, quality and safety of the cuts.Now many woodworkers make their own featherboards from scrap lumber, but here’s a better, safer option: the Bench Dog 40-011 Feather-Loc Double Featherboard. This popular router-table accessory consists of not one, but two industrial-quality featherboards. The featherboards are made from a high-tech polymer and each one has 13 angled fingers that apply steady pressure that consistently produces cleaner cuts with less chance of kickback, chattering or lifting.The featherboards slide into miter-gauge slots in the router table or fence, and are locked in place by tightening a pair of knobs. Note that Feather-Loc Featherboards can also be used on a table saw, shaper, bandsaw or any other woodworking machine with a miter gauge slot. -- Joseph Truini Feather-Loc is essential for holding your stock firmly against your tool's guide fence and tabletop. Use one on the table saw to keep long stock against the rip fence. On router tables and shapers, use one before and after the cutter. Attach Feather-Locs to both the fence and the tabletop when routing long and thin stock on the router table. Not only will Feather-Loc protect your hands, it also helps prevent kickback, binding, and bent blades. Its durable polymer retains its flex memory, ensuring a steady feed rate. Feather-Loc's rounded feather tips will not mar your workpiece. The exclusive built-in setup feather makes setting the tension fast, easy, and repeatable. Next time you're machining tall, thin, or narrow stock, think Feather-Loc. Safer cuts. Better cuts. Every time. See below for which model suits your requirements.

Most helpful customer reviews 72 of 80 people found the following review helpful. Poor design and construction By Darryl Ramm I purchased several of these. Initially they looked good, but in use they are annoying and end up breaking. Most other commercially available featherboards are better designed, better built and cost less! I am surprised other reviewers rate these so high, I suspect the ratings are given before much use. 1. The black plastic knobs that you use to tighten the featherboard in place capture onto a nut head. The largest problem with these featherboards is that it is easy to strip the black plastic knobs when they are tightened, allowing the plastic knob to turn freely on the captive bolt. 2. A better design would ensure a more positive capture into the track slot by having both black knobs works to lock the split aluminum bar into the track slot, in this design only one of the knobs does this. Which BTW is the one that strips as above, since you have to tighten it enough to stop the featherboard sliding in the track. 3. The black plastic knobs are small and feel cheap, other commercial featherboards have larger knobs that are easier to tighten. 4. Also after using them for a while you've start to hate the non-parallel bolt slots that the featherboard slides around on. Most other commercial featherboards have parallel slots and these are easier to adjust. 27 of 29 people found the following review helpful. Came without the track bars By Dave P Maybe I didn't review it closely enough, but this product shipped without the bars to allow it to track in my table saw. Should have been more clearly evident. 17 of 17 people found the following review helpful. Usefull but awkward to use By E. Weber I have been using these featherboards for a little while now both on my router table and on my table saw fence. They do there job but I find it awkward and time consuming to set them up because of the non parallel slots. See all 28 customer reviews...

These new 1/4" thick aluminum plates all measure 8-1/4" x 11-3/4" - the exact size of our redesigned HPL router table's plate opening. Each one has a different mounting-hole configuration so that virtually every router on the market will fit one of the four pre-drilled options. The most popular routers on the market have been divided into Groups, with a plate being assigned to each Group. If your router isn't listed in any Group, either of our two un-drilled plates can be easily customized to mount your tool. All plates include an insert with a 1-1/2" bit opening. Optional inserts sold separately. Group A Routers, with 3-1/4" Plate Opening: Makita 1100; Milwaukee 5615-5624; DeWalt 616-618; Bosch 1617- 1618; Rigid 2930 Combo Kit; Porter Cable 690, 890, 7529, 97529, 8529; Hitachi M12VC (Fixed & Kit). Group B Routers, with 3-1/4" Plate Opening: DeWalt DW621, DW621k; Crafstman Standard; Freud FT1700E. 1702VCEK Group C Routers, with 3-11/16" Plate Opening: Porter-Cable 7518,7519, 7538, & 7539; Milwaukee 5625-20; Triton TRA001 and MOF001 Group D Routers, with 3-11/16" Plate Opening: Bosch 1619-1619EVS, Freud FT2000; DeWalt 625 Standard Blank Plate, with 3-1/4" Plate Opening: Blank plate option for drilling custom mounting holes for standard size routers. Large Blank Plate, with 3-11/16" Plate Opening: Blank plate option for drilling custom mounting holes for larger routers. Every heavy-duty aluminum plate includes an insert with a 1-1/2" bit opening, plate-locking bolts for our new leveling and locking system (Shown at right), and router-mounting hardware.

Amazon Sales Rank: #263481 in Home Improvement Brand: Rockler

Handles hot-melt adhesive wood and polyester edge banding. Comes complete with a heavy-duty industrial heat gun. Guides are completely adjustable and will accommodate materials as wide as 2-1/4". Capable of applying edge banding to straight and curved edges.

Amazon Sales Rank: #86384 in Home Improvement Brand: Freud Model: EB100 Handles hot-melt adhesive wood and polyester edge banding Works on straight or curved edges Guides are completely adjustable and will accommodate materials as wide as 2-1/4 inches Comes complete with a heavy-duty industrial heat gun Manufacturer's 1-year limited warranty

The Freud Difference Freud manufactures some of the most innovative, technologically advanced saw blades in the world. To ensure that the highest quality products meet the toughest design standards, Freud owns and operates six manufacturing facilities in Western Europe. Freud is one of the few manufacturers of woodworking tools in the world that produces its own MicroGrain carbide with titanium, called TiCo -- a combination of titanium and cobalt. Freud develops different types of carbide for each application to maximize the cutting life and performance of the tool; and Freud also operates one of the most modern product development research centers in Europe. By overseeing the entire manufacturing process from start to finish, Freud guarantees some of the highest quality, most advanced products in the industry. About Freud's Industrial Power Tools Freud manufactures a wide assortment of quality power tools and accessories to suit any woodworking project. Freud power tools have gained recognition from several of the industry’s trade publications, including the coveted "Top 10 Innovative Tool" award from Workbench for our FJ85K Heavy Duty Variable Speed Jigsaw and the prestigious "Best Buy" award from American Woodworker magazine for our JS100A Biscuit Joiner. About the Edge Banding System The Freud Edge Banding System can handle hot-melt adhesive wood and polyester edge banding, and comes complete with a heavy-duty industrial heat gun. The guides are completely adjustable and will accommodate materials as wide as 2-1/4 inches. This system is capable of applying edge banding to straight and curved edges. Warranty The edge banding system is covered by Freud's 1-year limited warranty. The Freud Edge Banding System can handle hot-melt adhesive wood and polyester edge banding tape and comes complete with a heavy-duty industrial heat gun. The tape guides are completely adjustable and will accommodate materials as wide as 2-1/4 inch. It is capable of applying edge banding tape to straight and curved edges.

Most helpful customer reviews 51 of 54 people found the following review helpful. The "Best of Breed" -- By Default By Timothy S. Rumbinas The Freud edge banding system occupies a unique niche between the household iron and multi-thousand dollar (aka "real production") edgers. So far as I can tell, it's the only option for semi-professional production of heat-set edge banding.I find it a highly compromised tool. As the old National Geographics used to say, it's in a land of problems and promises. Conceptually, it's a darn good idea. The execution could be a whole lot better.Let's look at edge banding for a minute. It's not much thicker than a business card (exclusive of adhesive)and only fractionally wider than the wood it is applied to. It takes a fair amount of heat to soften the glue. The guide system on a bander needs to hold material flat, square and unbowed, although everything that is being done previously almost guarantees the opposite.The EB100 sometimes does the trick. There's only so much precision one can expect from stamped steel guides. When the machine works, it's a lot faster than the household iron. When it doesn't, it's hard to resist the temptation to throw the sucker out the window. Although one can remove improperly applied edging, it takes more effort than to apply it by hand in the first place.Freud should improve the guide system and the table on the EB100 to make it a truly useful machine. Machined, precision guides would are necessary for this operation. And they shoud re-think using heat-set banding on a machine table that is subject to high temperatures. After 20 minutes of operation, the front edge of the table peels up. This doesn't impair function, it just looks like hell.I know woodworkers that get excellent results from this system. Despite significant experience with precision machinery, I can't duplicate their results. Maybe if I were more skilled, I could. I am uncomfortable with a machine that makes me guess continually. 10 of 10 people found the following review helpful. great buy! Just be patient. 100x better then an iron!! By B. HOLM If you do any kind of pre glued edgebanding with an iron and you dont want a huge machine or just cant afford one this is great. At just under $300 this paid for it self 10 times over in my first job. Yes it was tough to get it figured out lining it up perfect so your tape does not run off the edge of your panel, but once you get it its a snap. Do not rely on the rubber feet to keep it in place I press hard to make sure the tape is on there so I had to drill some hole just behind the fence and screw it down to the work bench. Also the rubber/polyurethane wheel with the skate board wheel bearings on it seems to be a little cheaply made. the bearing on one side is not perfectly in the center. maybe 1/32" off but causes the tape to run up the wheel instead of strait. so I took it off and flipped it upsidown. works great. I also set the machine back on my work bench and extended the table so that i could band wider panels. I do think its still faster to edgeband 24" x 96" panels with the iron. just to big for this machine. Oh and one more thing, when I first started using it I noticed that the tape did not stick really really good every now and then so just to make sure after every panel I pull it off the machine and roll it with the same roller I use with the iron ( takes only 2 seconds but well worth the time for insurance.) And if I were you, if you dont already, get a laminate trimer to flush trim the tape. dont mess with the knifes you slide on there. I use the Bosch Colt and love it. I use a 1/16 or 1/8" roundover bit and set it so that the radius just barely touches the top of the tape. Gives it a flush trim and a slightly eased edge the just hit it with some 320 sand paper and your done. 1 of 1 people found the following review helpful. Leaves a little to be desired. By Reynaldo Mendez This product worked well enough on a recent project that the

Now includes new 6.0 Software! As the bigger brother to the original CNC Shark, the diversely capable CNC Shark Pro offers twice the workable area and increased strength, making it perfect for a wide variety of larger machining, routing, and engraving projects in wood, metal, or plastic. Overall travel: X: 24'' Y: 24'' Z: 4.25''. Along with impressive power, speed, accuracy, and ease of use, it features a 1'' thick removable laminated particleboard removable work surface, plus 12 precision linear bearing guides (4 on each side) for maximum rigidity. A 24V supply provides full power to the powerful 1.8 degree steppers. Plus, the package includes a free download USB control software. For those who own different CNC programs, the Shark Pro can also interface with a number of programs in the industry. For a complete CNC system, you simply won't find a better value than the CNC Shark Pro. (Requires a computer with a USB port). This unit requires a Bosch Colt Palm Router for operation. Made in the U.S.A. Please note: This item can only be shipped within the 48 Continental United States and Canada.

Amazon Sales Rank: #128846 in Home Improvement Brand: CNC Shark Increased workspace and strength than original CNC Shark Overall travel: X: 24'' Y: 24'' Z: 4.25'' Features a 1'' thick removable laminated particleboard Now includes new 6.0 Software This unit requires a Bosch Colt Palm Router for operation (sold separately)

Most helpful customer reviews 4 of 4 people found the following review helpful. The Rockler Shark Pro... By Shane The Rockler Shark Pro made by Nextwave and sold by Rockler is the next great thing in home manufacturing. Given a pretty high sticker price it is very important for a machine like this to be capable of producing products not only in mass production but in high quality as well and this machine does not disappoint. After ordering or picking up at a local Rockler outlet the customer will receive two large packages, one containing the gantry and the other containing the deck. The gantry box will contain the complete and assembled gantry packed within shrink wrap and a lot of packing peanuts. The deck box will contain the fully assembled deck wrapped in sheets of foam. Included in one of the boxes will be a small white box containing the control box. This control box is the heart of the machine and includes the emergency shut off switch, the power cable, the control to motor cables, and a USB 2.0 cable. After removing the deck from the box and placing it on a level surface you will need to place the gantry over the deck and use the included bolts to fasten the gantry to the deck. After this is done plug the cables from the motors to the control box and plug the control box power supply into 110V outlet. After plugging the unit in you may hear a very slight electronic whine form the servo's, this is normal. Take the USB cable and plug it into your laptop or PC. Read the manual and follow the install instructions needed to install the control program from the website stated. After the unit is ready you will need to install the VCarve program and 3DCut programs, this is done by installing the provided CD's. With all programs installed and the unit ready you will need to create a file within VCarve or 3DCut and save the toolpaths as a file to transfer to the control program. Much can be learned from Rockler Shark CNC forums and I advise you watch the included tutorials and youtube video links(see included links in the comments section). This machine has been a great addition to my upstart business and has expanded my abilities. I in no way regret the purchase and have been successful enough in its use to have made enough money to pay it off in short time. The only problem I have with the unit is that it only comes with two material hold down clamps and Rockler's website does not provide much in the way of CNC bits. I have found many bits on EBay including 1/8 bits that require a new smaller collet that is not provided with the palm router which is sold separately from the machine. ALL FEEDBACK IS APPRECIATED. THANKS AND GOOD MACHINING. See all 1 customer reviews...

Kreg PRS1040 Precision Router Table System is set to make a real name for itself in the industry. Includes a series of ground-breaking new features, including the innovative self-squaring t-square style fence, the fully enclosed tubular aluminum extrusion, and the steel-strut reinforced MDF top with its Easy-Slide Micro-Dot Skin, just to name a few. This item ships in three different boxes: the router table, the router fence, and the table legs.

Amazon Sales Rank: #6248 in Home Improvement Brand: Kreg Model: PRS1040 Dimensions: .0" h x .0" w x .0" l, .0 pounds Fully enclosed, aluminum fence for superior precision and dust collection Edge-banded MDF top absorbs vibration and noise; easy-slide micro-dot skin 9-1/4 by11 3/4 by 3/8-inch thick phenolic insert plate works with any router Individual fence faces allow table to double as a vertical jointer Dual reducing rings boast three independent leveling/lock-down screws

Taking design cues from high-end table saw rip fences, the Kreg Precision Router Table System features a fully enclosed, t-square style fence for complete use of your miter slot and small adjustments on the fly. Its vibration and noise resistant MDF table has a high-pressure laminate Easy-Slide Micro-Dot skin, which makes it easy to slide workpieces across the surface. It also boasts a precise insert plate that mounts to any router without the usual extra holes you don't need. Bottom-up levelers feature eight individual contact points for leveling accuracy, and dual reducing rings (2 inches; 1-13/16 inches) provide the convenience of Porter Cable guide bushing capability. For added flexibility, independent fence faces allow the table to double as a vertical jointer.Precision Router Table SystemAt a Glance:

Most helpful customer reviews 52 of 54 people found the following review helpful. Fragile parts By VanMan The 3 star rating is not meant to reflect the usefulness of the product or the accuracy of the work one can perform with it. It is a reflection of the robustness of some key components. The stand is very sturdy as is the laminate coated table top and the actual aluminium fence. There are some weak areas. The phenolic insert accepts either of 2 reducing rings. These rings are held in place by screws which are threaded into very small, very fragile threaded holes in the phenolic insert. It is extremely easy to strip the threads in the phenolic insert by over-tightening. There is no positive "stop" when the screws are in far enough. Exercise extreme care when installing the reducing rings. More disappointingly, the aluminium assembly which attaches the fence to the levered glide (and the glide itself) which attaches to the guide on the side of the table are extremely fragile. The assembly is held to the levered glide by 4 machine screws with brass washers. I stripped the threads in the aluminium parts tightening one of those screws, using a hand screwdriver gripped by my fingers only (i.e. I did not grab the screwdriver with a "fist grip"). I'm a lawyer and I am not noted for my death grip. There are 2 nylon screws which take the slop out of the levered glide. When I assembled my table one went in perfectly while the other cross-threaded as it entered the second piece of metal. This is not the first tool I have had to assemble from a myriad of parts. It is, however, one of the most fragile. The fence is billed as being similar to a table saw fence. In my view, that is a bit of marketing hyperbole. The fence does have a locking lever at one end like a table saw fence. Engaging the lever does not, however, lock the fence perpendicular to the side of the table. There is a tall twist knob at the opposite end of the fence that you tighten after aligning the fence properly. It certainly isn't a bad system, just not as effective as a table saw fence. 51 of 53 people found the following review helpful. Excellent Router Table for the money! By D. Vo If you are a serious woodworker, this is by far THE best router table to buy. I bought the complete table, fence, stand, casters & micro-adjuster. Every little piece of hardware was accounted for and very neatly packaged. The reliability and accuracy of the fence make it very easy to use. And if you don't want to drill the insert yourself, for 3o bucks, Kreg will drill it for you, shipping included. The assembly instructions were written in simple, easy-to-understand English and not like the 'Chinglish' from other manufacturers who outsourced their products. This router table examplifies American ingenuity & workmanship. It's definitely a 5-star rating. 24 of 24 people found the following review helpful. Kreg Router table By David Conaway Sweet table! I'm not a master woodworker or great furniture maker, but this table is one of the greatest additions I've made to my shop in quite awhile. Smooth operation, easy to use and accurate. You won't be disappointed. The only item I'll add is a router lift. See all 22 customer reviews...

Amazon Sales Rank: #112432 in Home Improvement Brand: Porter-Cable Model: 9690LR Number of items: 1 Dimensions: 11.88" h x 11.50" w x 9.25" l, 11 Amp motor producing 1-3/4 Peak hp 27,500 rpm single speed motor Cam lock lever enables simple coarse height adjustments and motor release (fixed base) Micrometer depth adjustor accurate to 1/128-inch Dust-sealed switch and sealed ball bearing construction enhance tool durability; Precision machined aluminum motor housing and base

The Porter-Cable 9690LR 11 Amp 1-3/4 Horsepower Fixed Base Router makes easy work of even the toughest routing jobs. The powerful 11 Amp motor generates speed of 27,500 RPM for ultra-clean cuts. Bit changes are quick and easy with the 9690LR's auto-release collet system. This router comes equipped with a 1/4-inch and a 1/2-inch collet, so it will accept a variety of shank bits of these either of these sizes. Durability is a priority in the 9690LR, and it shows with its dust-sealed switch and sealed ball bearing design that keeps dust out of the tool's vital components. This router is also extremely comfortable to operate, and the overmolded rubber handles provide a secure, pleasant grip while operating the router. Porter-Cable 9690LR 11 Amp 1-3/4 Horsepower Fixed Base Router with 1/4-Inch and 1/2-Inch Collets

Most helpful customer reviews 23 of 23 people found the following review helpful. Feature packed easy to use. By EFS I purchased a 9690LR to replace the spindle lock on crapsmen router broke. I use this smaller router for all my hand work, dovetails, dado's, etc. I have a more powerful router mounted to a table. There are sereval things I like about this router, and one minor complaint. First, there are two complete collets (1/2 and 1/4") included, not a 1/2 and an insert. Second, I have cussed other routers with stuck bits. The collets have a snap ring around the collet just above the locknut. This allows the collet to be pulled out of the spindle by the nut. Very cool - no more anxiety attacks switching bits. Secondly, the spindle has a fixed hex nut just below the collet to provide the 'spindle lock' with a wrench. This double-nut mechanism is far superior to any spindle lock schemes on other routers. The depth adjustment and associated lock is very accurate and easy to use. Power switch has a rubber dust cover. My only gripe is the lack of an effective soft start. Since I use this as a hand router, I have one hand on the handle and another on the switch. I cannot hold this powerhouse still when it switches on, bit of a dangerous situation - for me and my project. With this in mind, I think I would go with the variable speed design of this model for the extra $20 if I had to buy it again. 20 of 21 people found the following review helpful. A superior value By A Customer This is one of the best power tools I've ever owned. I am not a professional woodworker, but depend on a router for many household, furniture, and art projects (making canvas stretchers and picture frames.) I bought it a few years ago (90th anniversary edition #90690) to build a couch in oak. This one came with 1/4 and 1/2 inch collets, an edge guide, and a metal case. The finish is silver and not the putty color on other models.This is my third, and I am sure, my last router. Previously, I owned a 7/8 hp generic brand which burned out, and a 1 1/2 hp Sears unit that wouldn't keep from wandering down in the base, and also seemed to strain in all but soft wood. The solid construction and slight 'kick' when turning it on were immediately very pleasing. The power was appreciated on that first project whether making 'step' joints, cutting mortises (using the template guide that I bought seperately), or cleaning up less that smooth saw cuts. I built a simple table for it that is extemely useful, turning the router into a basic joiner or a milling machine for picture frames and mouldings. Even the depth guide on the base is accurate and stays true.The torque is much higher than that of my other routers, which makes it safer and seemingly incapable of binding. The plunge base would be nice, but I can make the plunge cuts that I require by hand. Not sure I'd do this with less than 1/2 inch bits though.This is a great tool and a superior value. 6 of 7 people found the following review helpful. Very smooth powerful machine By Everett Smiley this tool works flawlessly, easy to insert router bits and easy to adjust tool for the job at hand, the noise level seems lower than most routers I have operated, and the tool has plenty of power to plow thru the hardest of hardwoods... See all 9 customer reviews...

Take advantage of production routing without dedicating lots of space in your shop. This Bench Top Overarm Router bolts or clamps to the top of your workbench and features pneumatic foot control to lower the router into the workpiece, letting your hands control the movement of the workpiece over the pin insert. If you already have a portable router, router bits and air compressor and do or plan on doing any type of production routing, this Overarm Router and your shop made patterns are all you need. Features: 4 plastic router collars fit most router bodies on the market Three reversible pins Spindle travels on double cylindrical ways Foot control allows hands free operation Pneumatic driven head Precision milled cast aluminum table Clear plastic safety guard Adjustable depth stop Specifications: Maximum head stroke: 5-1/2" Maximum distance spindle to table: 6-1/2" Maximum distance housing to table: 8-3/4" Throat capacity: 18" Router collar sizes: 4-1/4", 3-21/64", 3-1/4" and 3-1/2" x 2-5/8" high Router housing diameter: 4-1/2" Air pressure required: 60 PSI Table pins: 3/16" x 1/4", 5/16" x 3/8", 7/16" x 1/2" Table size: 19-3/4" W x 14" D x 1-3/8" H Overall size: 21-3/4" W x 28-1/4" D x~31-3/8" H Approximate shipping weight: 55 lbs.

Amazon Sales Rank: #347789 in Home Improvement Brand: Shop Fox Model: W1736 4 plastic router collars fit most router bodies on the market Overall size: 31-3/8"H x 28-1/4"D x 21-3/4"W Table pins: 3/16" x 1/4", 5/16" x 3/8", 7/16" x 1/2" Foot control allows hands free operation Maximum head stroke: 5-1/2"

Most helpful customer reviews 4 of 4 people found the following review helpful. A Great Tool For Those Special Applications By BJO This tool has come in handy for those special circumstances that involve duplicating templates where working from an overhead position makes the operation very safe and easy to navigate. I installed a Porter Cable model 7518 motor housing into the unit which provides all the power you'll ever need. The unit works smoothly with my small compressor and once you get used to feel of the foot pedal you'll be able to control the up and down pneumatic movement of the unit with ease. You have to be careful and make sure you do not attempt to remove too much material in a single pass. I did break a couple of spiral bits before I learned my lesson. I rigged up a small section of 1.5 inch of PVC pipe that I strapped to the side of the router to serve as a dust collection intake. It works fairly well. I actually used the unit to also make a pair of custom decorative shutters by routing diagonal mortises in the stiles of the shutters, an operation that would be nearly impossible on a router table and probably require an intricate jig with a freehand router. With the overhead router, it proved to be a fairly simple milling operation. I would definitely recommend this machine as a solid performer. I am always finding more and more uses for it in my shop. 0 of 0 people found the following review helpful. You get what you pay for By D Roddington This thing pretty much sort of works most of the time. My main beef is the bit doesn't really center on the pin because the hole in the table is too big for the .500 pins by about .005, thus pushing it to the rear when tightened with the set screw. This is a problem if you need precision results. Also the arm itself tends to wander around, and drift even further off center. Also the depth stop is imprecise to say the least, and all the air lines cracked and had to be replaced in the first year. I have put quite alot of time into trying to fine tune this machine and make it work, however, the limitations of its engineering prevent lasting effectiveness. There's really nothing else in this price range available, so if you must, you must, but don't think you're getting a professional quality machine. See all 2 customer reviews...

RD1101 Features Quietest (81dB) and lowest vibration router in its class. Soft start feature for smooth start-ups. Electronic speed control maintains constant speed under load. Sub-base accepts industry standard template guides for convenience. Rugged aluminum motor housing with small 3-1/4" diameter for easy handling Durable flat top design for stability when changing bits. Industrial cam-lock for fast and easy depth adjustment and removal of motor. Bits are installed/removed with two identical size wrenches. Powerful industrial 11AMP motor. Front knob can be placed in two locations for left or right handed operators. All ball bearing construction for long tool life. Large calibrated depth control ring for easy depth adjustment. Accepts 1/2" and 1/4" shank bits

Amazon Sales Rank: #57590 in Home Improvement Brand: Makita Model: RD1101 Number of items: 1 Dimensions: 9.50" h x 6.00" w x 12.00" l, 7.90 pounds Quietest (81dB) and lowest vibration router in its class Electronic speed control maintains constant speed under load Soft start feature for smooth start-ups Rugged aluminum motor housing with small 3-1/4" diameter for easy handling Sub-base accepts industry standard template guides for convenience

Most helpful customer reviews 28 of 29 people found the following review helpful. smooth operator By Toolpig I expect Makita tools to be better than most. This router is no disappointment. You won't believe how quiet it is until you use one for yourself. I like that I can use my existing Porter Cable accessories with it. As far as fixed base routers go , I have 3 PC 690's and the Bosch D handle. Iv'e also hade few craftsman, B&D and Dewalt routers. I like this one better. Why? It just feels right. It runs so smoothly. It's easy to adjust.It is very powerful. I like the simple but effective lock mechanism. Most of all it is so quiet compared to the others. The only thing I would change is I would add an arbor lock. I don't like using two wrenches to change bits. Are you listening Makita ? That is a very minor point and doesn't tarnish my over all opinion of the tool. If I had to go with only one router this would be the one. No hesitation , no thinking about it, no contest this is the best on the market. 23 of 24 people found the following review helpful. THIS IS ONE SUPER ROUTER By JAMES MILLS I HAVE BEEN USING MY NEW MAKITA RF1101 FOR ABOUT A WEEK NOW,OH MY GOODNESS WHAT A ROUTER. I FELL IN LOVE WITH IT ON THE FIRST JOB. I BUILD HIGH END CUSTOM FURNITURE IN MY SHOP IN LUBBOCK TEXAS AND I HAVE ALL MAKES AND TYPES OF ROUTERS INCLUDING THE MAKITA 3601C WHICH IS THE LITTLE D HANDLE ROUTER THAT SO MANY WOODWORKERS HAVE FALLEN IN LOVE WITH, ANYWAY, THIS NEW MAKITA IS POWERFUL WITH A 2 1/4 HP MOTOR I RAN IT IN GOOD HARD MESQUITE AND IT NEVER LOST SPEED NO MATTER WHAT SPEED I WAS RUNNING IT ON. I ALSO TRIED IT ON SEVERAL OTHER JOBS WITH DIFERENT WOODS AND FOUND IT TO BE JUST AS GOOD. IF I COULD OWN JUST 1 ROUTER I KNOW IT WOULD BE THIS NEW MAKITA. ALSO I WENT AND BOUGHT THE MAKITA RD1101 D HANDLE VERSION. THESE ARE ABSOLUTELY THE BEST 2 ROUTERS THAT I OWN. I OWN 9 ROUTERS BEFORE THESE 2 NEW MAKITA'S AND I FEEL THAT THE DUST WILL SETTLE ON THOSE 9. THIS IS THE FIRST ROUTER THAT I HAVE EVER FELT THIS WAY ABOUT. IF YOU ARE LOOKING FOR YOUR FIRST ROUTER THIS IS IT. IF YOUR LOOKING FOR ANOTHER ROUTER BUY THIS ONE. I FEEL SURE THAT YOU WILL SOON AGREE WITH ME ABOUT THESE NEW ROUTERS FROM MAKITA 15 of 15 people found the following review helpful. Makita D Handle By Bob Feeser The Makita D Handle is a super unit. It is so light and quiet, that it soon, will become your favorite hand held router. The stability of the D Handle configuration, is all the more reason. Their is no router that is a catch all, but this one is at the top of the heap for a favorite handheld. Two and one quarter horse power is great for most all applications. The smaller opening on the base lends itself to improved stability when working over smaller stock. The Makita is incredibly quiet. I thought I couldn't love a router more than I love my Fein, but this Makita has earned a side by side spot in my heart. The Fein is so light that it is excellent as a hand held, yet strong enough to be classified as an industrial production machine. Pertaining to the self locking collet, as found on the Fein, the Makita uses the twin wrenches. I am equally happy with both systems. The twin wrenches are easy to use. Centering your attention on the fact that your hands are actually stronger at squeezing two opposing arms together than your complete arms are, you understand the beauty of attaching the wrenches carefully, then squeezing to make a very secure clamping. By the way, the second resistance that is felt when removing the bit is a safety issue. If you have ever experienced a dislodging bit go flying across the room, you will know the second grip as a real asset. Some get confused, and wonder why when the nut is loose, the bit won't come out. Loosen it some more to the next tension before removing. The Makita has a flat top, so you can turn the unit on its head for easy access for bit changing. My initial interest in the Makita D Handle, is that I noticed Norm Abram using the

Mini Saw attachment for the Dremel MultiPro rotary tool. This unique attachment allows cuts through wood like never before. It attaches in seconds and makes clean, straight, perpendicular cuts up to 1/4 inch thick. Use for DIY, hobbies, crafts and modeling. Also cuts through paneling.

Amazon Sales Rank: #5156 in Home Improvement Brand: Dremel Model: 670-01 Number of items: 1 Dimensions: .0" h x .0" w x .0" l, Mini-saw attachment for rotary tools; clear housing for better visibility Cut quickly and easily through wood up to 1/4 inch thick; straight, perpendicular cuts Clear plastic housing Includes 1 rotary tool attachment; rotary tool not included 2-year limited warranty

The Dremel 670 Mini Saw Attachment, for the Dremel MultiPro rotary tool, is a unique attachment that allows cuts through wood like never before. It attaches in seconds and makes clean, straight, perpendicular cuts up to 1/4 inch thick. Use for DIY, hobbies, crafts and modeling. Also cuts through paneling.

Most helpful customer reviews 53 of 54 people found the following review helpful. Not new, but useful By David Brazelton Dremel had a saw blade bit an number of years ago but withdrew it, probably because there was no blade guard. Now they have solved the blade guard problem and by angling the tool a bit have made it able to cut in the center of a board. It took a little getting used to before I got comfortable with it because the guard tends to fight you a bit until you develop the technique to open it properly as you start the cut. It is limited to 1/4" depth of cut making it specifically a modelers tool. When used for what it does best, it is great. 43 of 44 people found the following review helpful. Yes, but... By Rachel Mello I use my mini-rip saw all the time; it's absolutely essential to my art work. But I can't recommend it without a few comments. First: that safety housing around it is so bulky that you cannot really see where the blade is going to go, exactly. This is fine if you're cutting something roughly, and you don't care within an 1/8 of an inch where the blade touches your work, but otherwise it's maddening. When I first bought it I tried it for a few cuts then put it aside to return. Instead what I did was attach it into one Dremel and use my other one, with a diamond cut-off wheel inserted, and lop the whole front of that silly cage off. If you do this, be mindful of where it is sealed to keep in the lubricating oil, and leave the back face of the safety on to help you keep the blade straight up and down. Once you do this little surgery, of course, you're out of warrantee, but then, WOW! this little guy is super handy! It's a detail saw with a dream-kerf of about a millimeter. Make SURE you wear goggles, now, dust and bits are going to fly. Second: I don't know the solution to this second problem. I used my mini-saw so much, for so long, cutting through tempered hard-board that the blade got quite overheated and warped. When I finally realized I should have changed it a while ago, I found that the screw holding it in had fused to the blade and I couldn't get it off. The spindle-lock for the tool gave out before the screw moved, and I ended up bending the shaft of the saw trying. I would have returned it to Dremel, but since I had cut off the safety as I described, there was no chance. Ultimately I decided I had gotten far more than my money's worth out of the tool anyway, and bought a new one. I still use it every day. I guess I'm just going to have to be careful to change the blade sooner this time. 31 of 31 people found the following review helpful. Awesome little saw By A Customer I am amazed at the clean cut that this saw makes. I suppose it depends on the material you are cutting, but more often than not get a smooth, precise cut with no ragged edges. The saw is also remarkably easy to guide and cut a straight line. It's very well put together and I've had no negative issues with it whatsoever. See all 24 customer reviews...

Amazon Sales Rank: #98265 in Home Improvement Brand: Steel City Model: 35990C Number of items: 1 Motor: 1-1/2 HP TEFC, 120V/240V, 13/6.5 Amps Blade RPM: 3,450 RPM Seamless Cast Iron table top provides the best environment during operation. The precision-machined cast iron trunions are mounted to the top cabinet to ensure perfect blade alignment, increased stability and ease of adjustment Warranty: 5 Years

10-Inch Contractor Table Saw w/ Cast Iron Table Top

Most helpful customer reviews 19 of 19 people found the following review helpful. Minor Assembly Issues But an Excellent Saw and Value By P. Anzalone I chose this saw because it had high end features at a price that was in my range. The main features that made me choose it were the cabinet mounted trunnions, the built in mobile base, and the cast iron extension wings. First of all, this thing is built like a tank and the motor/belt already comes mounted in the cabinet which helps with assembly. Everything was packed nicely and the freight delivery was top notch. Now comes the only negative part of my experience...the assembly. Assembly was not difficult, however, the instructions are completely useless. The instructions would call for some screws or bolts that clearly were not provided and after a while I basically used whatever bolts would fit the task at hand, completely disregarding the instruction manual. Although a bit frustrating, I still assembled it in about 3 hours only needing help from another person to attach the cast iron wings. The seamless extensions are pretty cool and give the saw a great look and feel. The only issue is that with the seam concealed in the miter slot if the wings are not completely flat/level, the miter slot changes width ever so slightly causing the miter gauge to bind up. After about 30 min of adjusting the wings (instructions say they are leveled at the factory, but for me that was not the case), the whole table was perfectly flat and the miter slot was tight and smooth. The fence is good, but not excellent. It would have been nice for the front rail to be all one piece. The saw passes the nickel test and moves fairly easily with the mobile base. Cuts are smooth and accurate and its actually much quieter than I expected. Although the assembly process was needlessly frustrating, the overall value and quality of this saw is exceptional. In my opinion, whatever money Steel City saved by having a 3 year old write their instructions was worth it since that money clearly went into the quality of the parts. That is why I'm giving this saw 5 stars. 9 of 9 people found the following review helpful. Great saw for the money!!! By Adam W. Williamson I have been without a table saw for a while, and spent most of that time dreaming and researching on which saw to buy. I feel safe in saying that the major piece of woodworking equipment in a shop is the table saw, and research should be done to find the right saw for your application. This saw at this price is a good deal. The money you will save can be applied to other items to increase the efficiency of the 35990c. Some of the pros to this saw are: enclosed cabinet, cabinet mounted trunions, 4" dust port located in the bottom of the cabinet, quiet opperation, built in mobile base, and good safety equipment. After set up, I was able to spend about an hour adjusting and readjusting until I was content. An hour is not bad since I was not in any hurry. The adjustments are fairly easy, and I do not fear readjusting in the future. There is, however, one bolt for the left table extension that is hard to reach, but it is still not that bad. The table top is made from three pieces of cast iron that conceal the seams in the miter slots. I'm not sure if the seam being visible or not actually makes a difference in performance, but it does make the miter slots adjustable. To me this is a big plus. Lots of people buy incra miter guages for the ability to remove the slack in the miter slot, but this seamless feature of the 35990c allows you to adjust some of the slack with the cast iron extension. I was lucky enough to have both the seamless table and the incra v27. I quickly reached for some scrap stock and made a 90 degree corner to check with an engineer square. I was extremely happy with the results. At a price of $649.00 with no tax or shipping, I find this to be a great deal, but there are some cons to this very positive report. There were several missing bolts,

Introducing Trends T4EK is a light duty 1.1 HP plunge base router with electronic variable speed motor. This plunge router is ideal for inlaying, sign making, edge molding or any other light duty routing applications. A convenient spindle lock makes short work of bit changing. With the easily removable router base, the T4EK motor is perfect for any power carving enthusiast. Includes three collets (1/4, 6mm and 8mm), a clip-in dust spout, a 5/8 template guide bushing, edge guide and storage case. Specifications: Plunge stroke 0 - 1- 3/8" Power Input 1.1 hp, 850 Watt, 120V motor No load speeds 11500-32000 rpm Bit dia. max 1- 3/16" Collet diameters: 1/4", 6mm and 8mm Dust spout size 1- 3/8" Template Guide bushing diameter: 5/8" Tool weight: 6 lbs Shipping Weight: 7.7 lbs Includes: Collets: 1/4", 6mm and 8mm 1- 5/16" Clip-in dust spout 5/8" Euro Style Guide Bushing Adaptor plate for Screw-on Guide Bushings Edge Guide Storage Case One Year Warranty

Amazon Sales Rank: #68115 in Home Improvement Brand: Trend Model: T4EK Number of items: 1 Dimensions: 6.00" h x 13.50" w x 17.50" l, Light weight Variable speed motor Plunge base Spindle lock Use for light duty routing, carving and die grinding

Trend's T4EK is a light duty 1.1 HP plunge base router with variable speed for hobbyist and light tradesman use. The kit includes two extra collets for use with metric tooling making the T4EK versatile enough to do some shaping, sharpening and carving tasks. Also included is a standard guide bush and an adapter plate for using screw-on type guide bushes. A dust spout for vacuum hook-up and a side-fence are also provided in the sturdy blow molded storage case.

Most helpful customer reviews 1 of 1 people found the following review helpful. Worth a Second Look By Michael Collyer Like the other reviewer, my Trend router developed a switch problem shortly after buying it. But my experience dealing with Trend was very positive. I contacted Trend via the email address on their Web site and explained the problem. The following day I received a courteous reply with a return authorization number and assurances that the problem would be resolved. A new router was shipped to me the very same day they received my defective router. As for the router itself, I was looking for a good quality light-duty plunge router but didn't want to spend $200 for a Bosch or DeWalt router and plunge base. I purchased the Trend T4 router for half the price. My impression was favorable. The tool is solid, the plunge action is reasonably smooth, and the variable speed motor is more than powerful enough for any light-duty application. I do a lot of free hand routing and found the Trend easy to maneuver. Operation is steady throughout the RPM range. For the money, I felt the trend was a solid value. When the switch broke, naturally I was irritated but felt that because the overall quality and construction of the router is good, that the defective switch was an isolated problem. The outstanding customer service that I received from Trend went a long way in reassuring me that Trend is serious about building a quality product and keeping its customers happy. 5 of 11 people found the following review helpful. trend router T4EK By H. Wilson This router sucks. It had a broken switch out of the box(I needed it so I fixed it with a rubber band)This was supposed to be brand new. I did not have 30 minutes running time on it and it quit. I sent it to the address it listed for warranty work...guess what...they moved! Their book did not say you needed a RA number just send it to that address. Okay UPS tried to send it to a new address...guess what...they refused it. Now it's floating around in limbo and even UPS doesn't know where. I want to point out that UPS has done more than they should trying to find the repair shop...not their fault. I didn't buy this router on Amazon (I have bought other stuff and am very well satisfied with them) Bottom line BEWARE of this thing. See all 2 customer reviews...

Amazon Sales Rank: #58532 in Home Improvement Brand: Big Horn Model: 10221B Dimensions: 1.00" h x 3.00" w x 10.75" l, Ergonomically designed handle Use to guide wood through cutters Keeps fingers away from cutters Provides extra control for small pieces

Push stick is designed for controlling stock when limited space is available. Keeps hands out of the way for maximum safety. Excellent when ripping with the table saw.

Most helpful customer reviews 15 of 15 people found the following review helpful. Dangerous Product By nada this product is dangerous,I used mine for probably 8 months before it actually touched the blade,but the first time it nicked my blade it literally exploded in my hand,when it happened its one of those times that it happens soo fast your in shock for a second before you start counting your digits to make sure their all there,I was able to search around my shop and find most of the pieces(a few were imbedded in my hand)and notice that the blade just barely grazed the outside of the stick,I count myself as being very luck that I still had my blade cover on because the forward motion of the push stick being there one moment and gone the next my hand would have definately ended up in the blade,Now I cant say why this happened perhaps because I live in the desert and it isnt uncommon for my shop to reach 140 degrees with A/C off in the summer,perhaps the heat dried out the plastic but from now on I will stick with shopmade push sticks 8 of 8 people found the following review helpful. You have to be kidding By Walt in Pittsburgh I am convinced on this item that the reviewers all must work for the manufacturer. Talk about a $5 piece of junk. Now, if this were selling for $2, I might rate it higher. This looks and feels like a child's toy. Make one out of a piece of scrap wood and save your money. 11 of 12 people found the following review helpful. Safety First By Wayne Cease A push stick will help keep your fingers away from table saw blade.The handle on this one has a nice shape and the notch makes gripping thick wood easy. If you do a lot of thin or long material you may want to look at a Stots push stick (Amazon sells those too). See all 18 customer reviews...

The Triton MOF001C 2-1/4-Horsepower Precision Router Kit boasts a push button mode changer that lets you switch from free to winder plunge with a 2 5/16-inch plunge depth, an automatic collet lock system allows single wrench bit changes from below the base (or above the table), full range micro-adjustment, integrated dust control and a fail-safe switch lockout system for added safety. Includes - a winding handle, an extended base plate with edge guide and circle cutter, 1/2-inch straight bit, 1/2-inch and 1/4-inch collets . The powerful 13 amp motor offers variable speed (8,000-21,000 RPM), soft start and electronic speed maintenance.

Amazon Sales Rank: #80429 in Home Improvement Brand: Triton Model: MOF001C Number of items: 1 Dimensions: 9.00" h x 16.00" w x 16.00" l, 16.23 pounds Micro winder enables continuous fine depth adjustment through full plunge range. Push button plunge conversion activates conventional plunge mode. Easy set, direct reading 3 stage turret for precise preset cut depths. Soft start and variable speed (with maintenance under load) provides the perfect speed for all cutter types. Multi function fence: Extended base for greater stability. Full fence adjustment for trenching. Built in circle cutter.

The Triton MOF001C 2-1/4-Horsepower Precision Router Kit boasts a push button mode changer that lets you switch from free to winder plunge with a 2 5/16-inch plunge depth, an automatic collet lock system allows single wrench bit changes from below the base (or above the table), full range micro-adjustment, integrated dust control and a fail-safe switch lockout system for added safety. Includes - a winding handle, an extended base plate with edge guide and circle cutter, 1/2-inch straight bit, 1/2-inch and 1/4-inch collets . The powerful 13 amp motor offers variable speed (8,000-21,000 RPM), soft start and electronic speed maintenance.

Most helpful customer reviews 67 of 67 people found the following review helpful. Great in the router table By Harry Beck I bought this router, based on a FineWoodworking review, to use in my router table. The appeal was: #1)being able to change bits from above the table (and NOT having to remove the router), #2)being able to adjust the bit height from above the table and #3)being able to do these without investing in an expensive router lift. It works as advertised - easy to adjust bit height, (mostly) easy to change bits from above the table. I am impressed that the collet rises well above table. Kudos as well to a well-designed, heavy-duty, plated, cast wrench. Nice collet lock (automatically engages when the collet is raised to full height). Smooth and powerful. It is mounted to my table, I located where to drill the hole for the adjusting lever (some sort of template would have helped...), and it seems to work well. As regards router table use, the only goofy thing to me is the on/off switch. You have to push back a safety cover before depressing the switch - in free hand use I think this would be an annoying extra step. In the table the annoyance is that I normally leave the router switch on, plug it into an outlet in my table, and operate it from an external switch - not a problem until it is time to change bits. Raising the collet above the table is supposed to engage a lockout (that little cover) so that you won't accidentally turn on the router while changing a bit. However if the switch is already turned on the collet won't raise all the way until you reach under the table and turn it off - and that's a little clumsy because it is on the backside. Then, of course, you have to turn it back on (clumsy) before starting out again. If you followed that - not a big deal, and I suppose it is a reasonable safety trade-off. I'll get used to it. One more thing that is a little odd is the plunge mechanism - I'm not sure why one would need more than a spring and a locking lever on a smooth set of plunge rods, but Triton seems to think so - there is an odd knob with a push button in the middle (and a locking lever). In the little bit I handled it free hand I didn't quite figure it out (I had to read the instructions for cryin' out loud!). This would only be an issue for me if I was using it free hand, and I'm not - my reliable Bosch routers do that for me comfortably. So, for router table: pretty great, especially for the price (less than most router lifts alone). For free hand use I don't think I'd pick it over the more conventional fare - Bosch, Porter-Cable, Dewalt, Makita, etc. It does come with quite a collection of extras for free hand use though, so you might want to handle it and compare prices. 26 of 26 people found the following review helpful. Excellent table router, bad switch cover By Jon McCoy I'm very impressed with this router, having replaced a PC690 in my Bench Dog table. I almost bought a 3+ hp router and lift ($500+), and now I'm glad I read that FWW review over Christmas break. It's very easy to adjust and swap bits -- especially compared to the PC690, which was quite tricky to adjust depth accurately. And it has plenty of power for the work I do, mostly narrow dados and rabbets in hardwood. My only complaint is with the power switch safety cover. My router table has an external power switch, but to change the bit you need to turn off the router's power switch as well. No biggie, just a nuisance. Except when I tried to use the router, the cover vibrated closed and powered down the router. A few screws later, the plastic switch cover & spring are no longer causing grief. 32 of 34 people found the following review helpful. Triton for Router Table By Steven L. Johnson I bought this router to mount in a table I was building. I now have many hours of use in this capacity and am exceptionally pleased. The only thing I haven't made good use of is the chip extraction attachment. This router is exceptionally well

New KT-2514 2011 version Lead time to ship is 14-30 Days. Travel of (Y)24" x (X)14" x (Z)5.5" (Shaft linear motion, compatible with nema 23 steppers and k2 servo motors) The new KT-2514-09 has 20mm shafts, antibacklash nuts, wider 19 inch material capacity. Use the accurate machine to cut thin aluminum, plastics, and wood. The anti-backlash nut and the .100" pitch leadscrews provide very accurate resolutions and is great for fine inlay work. The pitch provides great mechanical advantage when cutting hard woods and have been tested to cut .375" deep, at 70IPM, with a .375" diameter bit when used with Gecko drives and 280 Oz/in motors. With the right approach in your toolpaths, spindle, bits, accessories you can achieve results in milling that once required a $50,000 and more cnc machines. With the KT-2514-09 you now can do this in your own garage, business, or anywhere with 110V outlet. INCLUDED in auction: + New KT-2514-09 Frame (Shaft linear motion), + leadscrews .100" pitch and Kerk anti-backlash nut. + 3 Axis control box using gecko drive, CD for MAch settings. + 3 Stepper Nema 23 motor (275 oz/in). + Table Top with T-slots (2 inches apart, uses 1/4-20 nuts and screws) - Retails $275 + Mount choices: Porter Cable 892, Bosch Colt trimmer, Porter Cable 7310 only (we recommend the PC892). + K2 will ship with Porter Cable 892 mount if you do not notify a different model mount. + Cable Carriers. + Nema 23 mounts. + Home limit switches. Use these to home the machine. + Plugs for Home switches. + Settings for Mach 2 or Mach 3 with K2 machine profile CD/email and settings for gecko drives (Does NOT include full version of Mach 3 software with license) + Notice --- You may add more K2 options to this sale after this auction is won by you. + K2 will not remove items from the machine to machine it a lower in price.

Amazon Sales Rank: #473326 in Home Improvement Brand: KT2514 Model: KT2514 steppers Standard 5 inches of clearance and 5.5 inches of travel. Easy to assemble. 99% preassembled. Wider X axis clearance of 19 inches. In-line bearing arrangement on all axis for better longevity. 20mm shafts and bearing on all axis. All Axis uses Kert Lead screws and Kert Anti-backlash Nuts.

This full-service station combines all the value of a solid phenolic tabletop (durability, stability, low-friction, and more) with a full lineup of premium accessories. On top of the ProTop, you get the feature-rich 32" ProFence, a solid aluminum Bench Dog router plate to house your specific router, and Bench Dog's rugged steel stand! NOTE: Be sure to select a package that includes a plate pre-drilled for your router (see list below). Blank plates are also available for routers not found on the list. Group A Routers: Makita 1100; Milwaukee 5615-5624; DeWalt 616-618; Bosch 1617- 1618; Rigid 2930 Combo Kit; Porter Cable 690, 890, 7529, 97529, 8529; Hitachi M12VC (Fixed & Kit). Group B Routers: DeWalt DW621, DW621k; Crafstman Standard; Freud FT1700E. 1702VCEK Group C Routers: Porter-Cable 7518,7519, 7538, & 7539; Milwaukee 5625-20; Triton TRA001 and MOF001 Group D Routers: Bosch 1619-1619EVS, Freud FT2000; DeWalt 625 Blank Plates: Standard - 3-1/4" insert opening Large - 3-11/16" insert opening About the package: Bench Dog ProTop Tabletop With solid-phenolic construction, the 23-1/4" x 31-1/2" ProTop offers rugged durability and a low-friction surface for years of enjoyable use. An innovative recessed Dual-Track features a standard miter track as well as a Universal T-track that accepts accessories with 1/4" and 5/16" t-bolts, and 1/4" hex bolts. An 8-point leveling system supports the heavy-duty aluminum plate, keeping it flush and secure throughout your cut. Bench Dog 32" ProFence 3-1/2" tall, with a precision-machined aluminum frame for total flatness. Front and back T-tracks accept 1/4" t-bolts, 5/16" t-bolts and 1/4" hex bolts. Includes bit guard, adjustable melamine-coated MDF faces with T-slots, and dust port. Bench Dog Steel Stand With 1/8" thick steel components, this 18" deep x 24" wide x 32" tall stand includes four adjustable levelers and all assembly hardware.

Brand: Rockler

This package combines the biggest, toughest top on the market (Bench Dog's cast-iron ProMaxRT) with a ruggedly-built stand/storage unit for an all-around premium setup. Add the Bench Dog 32" ProFence and a heavy-duty aluminum router plate and you'll be set for pro-class routing in no time! NOTE: Be sure to select a package that includes the correct pre-drilled router plate (refer to the list below). Blank plate packages are also available for router not found on the list. Group A Routers: Makita 1100; Milwaukee 5615-5624; DeWalt 616-618; Bosch 1617- 1618; Rigid 2930 Combo Kit; Porter Cable 690, 890, 7529, 97529, 8529; Hitachi M12VC (Fixed & Kit). Group B Routers: DeWalt DW621, DW621k; Crafstman Standard; Freud FT1700E. 1702VCEK Group C Routers: Porter-Cable 7518,7519, 7538, & 7539; Milwaukee 5625-20; Triton TRA001 and MOF001 Group D Routers: Bosch 1619-1619EVS, Freud FT2000; DeWalt 625 Blank Plates: Standard 3-1/4" insert opening. Large 3-11/16" insert opening. About the package: Bench Dog ProMaxRT Cast-Iron Table At 24" x 32" x 1-1/2", the ProMaxRT is the largest, flattest, and most durable option on the market. Weighing in at nearly 100 lbs, the one-piece top provides more than 5 square feet of ultra-flat work surface, precision ground to within .008". Its 12-point plate-leveling/locking system guarantees a flush working area and keeps the aluminum router plate secure while cutting. Bench Dog 32" ProFence 3-1/2" tall, with a precision-machined aluminum frame for total flatness. Front and back T-tracks accept 1/4" t-bolts, 5/16" t-bolts and 1/4" hex bolts. Includes bit guard, adjustable melamine-coated MDF faces with T-slots, and dust port. Bench Dog Baltic Birch Cabinet Rugged bolt-and-cross-dowel construction combined with the strength of Baltic birch make this the ultimate stand. With ample storage, four leveling feet, and pullout router bit trays.

Amazon Sales Rank: #384086 in Home Improvement Brand: Rockler

Folds down in seconds for easy transport and compact storage. Legs foldup around router. Table constructed of HPL professional grade laminate. 24" aluminum fence, has intergral molded dust collection port. Adjustable MDF faceboards. Clear safety guard. Removable phenolic plate. Insert rings fit router bits up to 3-7/8". Precision T-style meter gauge track has precise fit for all standard miter gauges. T-slot for use with custom jigs, fixtures, and featherboards. Power switch and router not included.

Amazon Sales Rank: #280508 in Home Improvement Brand: Rousseau Model: 3110 Dimensions: 31.00 pounds Benchtop folding router table with a 24-by-19-inch work surface 1-1/8-inch thick with high-pressure laminate on both sides Precision machined 24-inch aluminum fence; precision T-style miter gauge track Deluxe router baseplate with leveling system; legs fold flat for compact storage Weighs 31-pounds; covered by a lifetime warranty

The Rousseau Co. 3110 Benchtop Folding Router Table is a necessary addition to any workshop. The large 24 by 19-inch worksurface is 1-1/8-inch thick and has high-pressure laminate on both sides. Included is the Rousseau Co. deluxe router baseplate with leveling system, precision aluminum fence with MDF face boards and aluminum t-style miter gauge track for attaching featherboards and jigs. The folding legs provide a 14-inch working height and are constructed from powdercoated steel tubing to withstand years of rugged use. The 3110 is only 4 inches thick when folded so it can be stored almost anywhere. The 3110 is covered by a lifetime warranty. The Rousseau Co. 3110 Benchtop Folding Router Table is a necessary addition to any workshop. The large 24" x 19" work surface is 1-1/8" thick and has High Pressure Laminate on both sides. Included is the Rousseau Co. Deluxe Router Baseplate with leveling system, Precision Aluminum Fence with MDF faceboards and Aluminum T-Style Miter Gauge Track for attachingfeatherboards and jigs. The folding legs provide a 14" working height and are constructed from powdercoated steel tubing to withstand years of rugged use.The 3110 is only 4" thick when folded so it can be stored almost anywhere.The 3110 is covered by a lifetime warranty.Optional Accessories Include: 3301-4 Deluxe Fence Upgrade Kit, 3301-5 Dual Pressure Featherboard and 3506 Power Switch.

Most helpful customer reviews 9 of 9 people found the following review helpful. Where are the instructions? By Builder from the Future Got this table a few days ago. It is built very well, and seems very sturdy. There are no, repeat, zero instructions sent with this table. Lots of screws, and knobs that I found places for most of, by looking at photos of the table on the internet, but still have a handful left over that I am sure would be useful if I knew what to do with them. The Rousseau website is rather minimalist as well and it was of no help. I actually got some instructions for how to mount my router (Skil 1825) to the baseplate from other reviews of the Rousseau baseplate that you can buy seperately on Amazon. You have to drill your own mounting holes. Not too hard, but again, without instructions it is. So that said, I have run a few pieces through and it works very well. You need some basic tools, t-square straight edge, to get everything aligned properly, but that too was easy. Easily adjustable fence, hole to attach your shopvac, miter gauge slot, but does not come with T-style miter gauge. The one off my table saw fits in the slot though and I use it. Not the cheapest table for sale here, but a nice compromise between price and quality. 2 of 2 people found the following review helpful. Missing a lot By S. Haynie This came knocked down in a box, missing two knobs and any coherent instructions. Lots of shims and washers that may go somewhere, but its not at all clear except from a basic knowledge of infeed/outfeed. The Rousseau plate has been reviewed elsewhere, its as hard to work with as noted with the snap in rings and the difficulty in mounting your router. Update: Credit where its due to Rousseau, Andy took my call, discussed the use of the shims and is sending out the missing knobs via USPS. Good customer service can make up for poor execution in shipping. 4 of 5 people found the following review helpful. Nice solid top, but that's about it... By James Bowen First the good: This table has a nice solid top with a full sized miter slot. The bad: Having said that, the fit and finish are very poor. The leg mechanism is held to the table with lag bolts, which is no problem. However, these were placed incorrectly and the bolts went in at an angle of approximately 25 degrees which IS a problem. rather than correct the problem, whoever assembled the leg set just bent parts to make them fit. this is almost criminal because the leg set is very solid and stable. And of course, The ugly: The fence is very heavy, which is a good thing. unfortunately, whoever assembled the thing must have been related to whoever applied the finish to the fence. It's the ugliest paint job I have ever seen, well since that time saw a car that had been painted with housepaint and a brush! The end result is that I built a cabinet and a fence for the top. So I ended up with a decent setup after all, but should I have had to? See all 3 customer reviews...

Get more from your Shop Vac! This versatile fitting slides onto standard 1-1/4" Shop Vac hoses, allowing you to hook up suction to 2-1/4" (I.D.) dust ports on router table fences, dovetail jig dust collectors and more. This is the only adapter that will connect Shop Vac hoses to the 2-1/4" ports on Bench Dog ProFence router table fences, Rockler Router Table Dust Ports, Rockler Dovetail Jig Dust Collectors and more.

Amazon Sales Rank: #61551 in Home Improvement Brand: Rockler Durable hard-plastic construction Tight friction fit Tool free set up no clamps necessary!

Most helpful customer reviews 2 of 2 people found the following review helpful. This thing is impossible to find locally By Jason Chance I bought probably 5 different adapters from the local big box stores trying to adapt shop vac hose to 2 1/2" DC fittings and none of them worked. I ordered one of these as a last resort and I'm glad I did- the tapered design fits snug down in a 2 1/2" DC port and doesn't come out without really pulling on it. Worth every penny for hooking up to my random orbital sander and saving my lungs. 1 of 1 people found the following review helpful. Fits Bosch Equipment By N. Peterson Unlike other products that were cited as bosch-fitting, this product fits my bosch 4100 table saw port and my bosch 1181 router table fence dust exhaust port. The adapter is tapered for a snug friction fit. The other end snuggly attaches to my shop vac. Exactly what I hoped to receive - no more duct tape! 0 of 0 people found the following review helpful. just the part i needed By Michael Mcdade the adapter is well made, not just a cheep plastic knock-off and very durable. there were no air leaks and the vacuum held very nicely. all in all, great performance at a great price. See all 5 customer reviews...

Add the Mast-R-Lift to your router table and take your fixed base router to another level, literally! Bit changes are convenient because the collet is accessible above the table. The Mast-R-Lift was designed for the most popular router motor on the market the Porter-Cable 7518 (3.5" diameter motors will fit with an appropriate adapter, sold separately). Each turn of the crank precisely raises the bit 1/16". The calibrated gauge makes it easy to make incremental adjustments as fine as 1/512" (less than 0.002"). The Mast-R-Lift is constructed of the highest quality components including a plate machined from 1" aluminum with a 3-1/2" opening that accepts the included phenolic insert to close the hole to 2" for smaller bits. Unique leveling bars are located at each corner to bring the plate flush with your router table surface. The medium plate is sized for 9-1/4" x 11-3/4" openings found on JessEm, Woodhaven, Woodpeckers, and many other router tables. The small plate is sized for 8-1/4" x 11-3/4" openings found on Bench Dog router tables. Includes an insert wrench, starting pin, and detailed instructions. Router motor is not included. Mast-R-Lift adapters allow you to use your 3-1/2" diameter motor (Porter-Cable 690, DeWalt 610, Bosch 1617, 1618, 1617EVS and 1618EVS) in the Mast-R-Lift clamp block. PC 7518 3-1/4 HP Motor. Spare the expense of the base and purchase only the motor of a Porter Cable 7518 Router. Includes 1/2" collet and wrenches.

Amazon Sales Rank: #81843 in Home Improvement Brand: JessEm Model: 02101 Dimensions: 9.50" h x 13.50" w x 16.50" l, Allows height adjustment and bit changes from above the table 9-1/4- by 11-3/4-inch insert plate size for JessEm router tables Built in plate leveling and insert adjusters for a perfect fit Includes a 1-1/2-inch insert ring with wrench, starting pin, and hex wrench Insert plate is machined with a 3-5/8-inch diameter TAB-LOC centerhole; 1-year limited warranty

Beautifully finished with red and black anodized components, the JessEm 02101 Mast-R-Lift is the sequel to JessEm's original ROUT-R-LIFT. Precision machined from premium 6061 aluminum, this is the top of the line for JessEm's lift systems. Designed for cabinetmakers, furniture makers and other custom woodworking pro's, the MAST-R-LIFT is built for long-term professional use. The design has been streamlined and performance has been enhanced with a full 3-3/4-inches of vertical travel. The insert plate is precision-machined from a solid 1-inch thick aluminum blank. Our new speed crank design offers a tall handle for clearing the top of the fence while making adjustments. Designed specifically for the Porter Cable 7518 and to fit similar cylindrical motor housings with the use of a reducer collar. The insert plate centerhole is machined to accept up to a 3-1/2-inch raised panel bit and includes a 1-1/2-inch insert ring. Additional insert ring sets are available separately. (9 1/4-Inch x 11 3/4-Inch)

Most helpful customer reviews 7 of 7 people found the following review helpful. Incredibly well made, very functional By J. Dubovsky I've used this router lift for a mix of wood-working jobs and haven't found much wrong with it. It's very well-made, the adjustments are solid but not too tight, and the height adjustment is quite repeatable. I like the fact that the included manual describes what you may need to do as the years go by; for example, they describe replacing the felt chip brushes on the shafts, knowing that you'll be using this thing for 10+ years. 8 of 9 people found the following review helpful. Very pleased By Rickey Lodico It took me all of 15 minutes to read the directions, remove the motor from my PC7518, install it in the Mast-R-Lift and have it ready for use in the router table. I couldn't ask for anything easier and it operates soooo smoothly too. 4 of 4 people found the following review helpful. Awesome Lift! By Tile Carpet Etc I had a little difficult time inserting my Milwakee router with the sleeve but eventually got it. I have used it extensively and having the ability to change the bit above the table is a luxury! I LOVE it! It's smooth and cranks nice and even both up and down. It is a little pricey but I know I won't have to buy another one, but I wouldn't mind having 1 or 2 more. I strongly advise anyone to invest in this quality tool rather than a cheaper one that you'll need to replace at least once. 5 Stars ***** See all 9 customer reviews...

The INCRA 1000SE, has all the great features of the popular INCRA Miter1000 plus more! The Special Edition adds a stainless steel Vernier cursor for an incredible 1/10th degree resolution between fixed steps. The Special Edition also includes a miter fence that telescopes from 18" to a full 30" in length with the new INCRA Flip Shop Stop for patented Automatic Positioning Control. The saw tooth rack system instantly controls the length of your cut with INCRAs legendary machine shop accuracy as the dual Flip arms provide flexibility. The Flip Shop Stop is equipped with three sliding stop rods that operate independently or in tandem for one, two, or three simultaneous stop positioner setups.

Amazon Sales Rank: #7014 in Home Improvement Brand: Incra Model: MITER1000SE Dimensions: 4.50" h x 18.25" w x 18.25" l, 8.12 pounds Engraved stainless steel primary scale for precision accuracy 41 laser cut V-stops for extreme accuracy at all popular angles Patented GlideLOCK miter bar with 6 expansion points for quick repeats 18- to 31-inch telescoping incremental miter fence for handling a variety of stock widths INCRA Flip Shop Stop-Fence Positioner for optimal mitering accuracy

Amazon.com Review A good table saw comes with a perfectly good miter gauge. But this Incra is perfectly great. It’s precise, versatile, infinitely adjustable and custom-fits to your miter gauge slot. You’re probably familiar with the Incra name because of their fantastic dovetail and box-joint-making jigs, but they’ve got a wide product line all with precision at the top of the list. An ingenious flip-stop locks down at any point along the fence for repeatable cuts, and it flips out of the way without disturbing your placement if you have other cuts to make as well. The fence actually telescopes out, from a closed length of 18 inches to a fully extended 30 inches for superior stock stability. The miter gauge itself has 41 detents in 5-degree increments across the entire 180 degrees, with special stops at 22-1/2 and 67-1/2 degrees, all gauged by angle indexing teeth for unparalleled accuracy. In addition, you can make 1/10th-degree adjustments with the stainless steel vernier cursor. The thing we like best about this jig is its ability to custom fit to your miter gauge groove, courtesy of six disks along the length of the slot bar. With a turn of an allen wrench, each one expands or contracts individually to get you the absolute best fit on your table, leaving you with zero play between bar and channel and zero chance for error. Incra’s also designed a neat top-mounted tab that fits a T-slot and removes in a few second for plain channels, letting you move the jig from your T-slotted table saw to other tools with a standard groove, such as a router table. We’re pretty taken with this setup, and we think anyone who craves precision will love it, too.--Kris Jensen-Van Heste The Miter 1000 Special Edition builds on the excellent foundation provided by the Miter 1000. The Incra exclusive AngleLOCK Indexing System delivers 41 lock solid angle stops in 5° increments over a full 180° range. Combine this with the included GlideLOCK Miter Bar, Telescoping IncraLOCK Cuto-off Fence and the Incra Flip Shop Stop, and you'll easily achieve mitering accuracy that you never thought possible. Whether it's your basic 90° cut-off, simple picture frames, or a 20-sided object, the Miter1000SE by Incra deiivers perfect, repeatable accuracy.... First time, Every time, Any angle. Six expansion disks adjust both sides of the bar for ZERO side play, anti-friction travel on all table saws with standard 3/4" x 3/8" or near-standard miter gauge channels, including Delta, Craftsman, imports, etc. This means that all of INCRA's incredible precision will actually show up in your work because the bar CAN'T wiggle around in the miter slot. This Special Edition Miter Fence telescopes from 18" to a full 31" length. Includes the Dual Flip Shop Stop and Incra's patented Automatic Positioning Control. Precision angle indexing teeth are laser cut in solid steel to lock in positive angle stops every 5 degrees over a 180 degrees range, with special stops at 22-1/2 degrees and 67-1/2 degrees. A stainless steel vernier cursor delivers an incredible 1/10th degree resolution between fixed steps.

Most helpful customer reviews 58 of 58 people found the following review helpful. Glad I Got It! By Vaughn McMillan Got the Incra Miter 1000SE a couple weeks ago (thanks to an Amazon sale price) and have nothing but praise for it so far. It was dead on right out of the box, although adjustments should be easy if ever necessary. There was very little assembly required, and Incra makes sure you have all the parts necessary (and then some...they threw in extra screws and other bits and pieces). One thing the Incra fence has that I've not seen on any of the others is the Incra "teeth" that engage the sliding stop. Very, very repeatable, and with the micro adjust screw, very adjustable, so you can get anywhere between the 1/32" teeth. Even though the stock gauge that came with my table saw has "stops" at 90 and 45 degrees, it was never trustworthy, so I had to check it each time I used it. I really like being able to set the Incra miter gauge at 45 degrees (or any other setting) and using it confidently without first checking to be sure the angle is right. The gauge seems rock solid. I've seen no flex issues. The bent sheet metal aspect of the gauge head is very substantial (IMHO) and I've not seen any evidence of flex with the fence extenced out. Granted, if I grab the extended fence and try to slide the saw sideways across the shop, it'll flex some, but I've not seen any flex in normal, reasonable use. I found it useful to add a piece of scrap 3/4" material for a sacrificial fence extension, but Incra includes the necessary screws, and the sliding stop can be quickly adjusted to accomodate the additional fence thickness. All in all, it's a well thought out and nicely executed product. 26 of 26 people found the following review helpful. Finally, accurate miters from my table saw! By Michael A. Campbell I had used the factory miter gauge that came with my Ridgid TS2400 table saw on a few projects and even after saw and miter gauge calibration I was still coming up with inaccurate miters. I decided it was time to buy a new miter gauge. I was researching miter gauges and had narrowed it down to the Osborne EB-3 and the Incra Miter 1000-SE. The Osborne had a number of disappointing reviews so I decided on the Incra. I could not be happier with my purchase. Setup took around a half an hour and was very easy. Within an hour I had already put the miter gauge to the ultimate test and had cut and assembled an octagon out of some scrap wood. The octagon came out perfect proving the miter gauge was set up correctly and that it is dead accurate. The only complaint I have is in order to make adjustments to the fence you have to use the tool Incra provides (I guess I could replace their screws). Other than that, I absolutely love the Incra Miter 1000-SE and can see myself now using my table saw more for miters rather than my chop saw. 20 of 21 people found the following review helpful. lots of adjustments you must play with By Dominic The Incra does have a lot going for it. In its price range, it is much better than the Kreg. It is not as nice as the Jessem but then your not paying the big Jessem price. I am not that crazy about the split nylon washers they use to take the slop out of the table slot. I had to play with that a good while but when you get it right it feels pretty good. we'll see how long it holds up without readjusting. The other thing the bugs me is the "erector set" way you have to shim, adjust, readjust, all kinds of things. I dont want to spend time doing these things, just make my cuts and get on with my project. The instructions do get a bit confusing too. When you get it all set up it does do a nice job and the quality is very good. I looked long and hard at many models and this one is the best all around without spending more than what your tablesaw might have cost. See all 72 customer reviews...

The Router Razor 200 will work with the following routers: BOSCH 1619EVS 3-1/4HP; BOSCH 1166 Plunge Base; Fein RT1800 3-1/4HP; Makita RF1101 Plunge Base; MLCS Marvel 60; Triton TRC 001; Fein 1800

Amazon Sales Rank: #89545 in Home Improvement Brand: Router Technologies Model: RZ200 Use it in a router table or hold it by hand Makes height adjustments quickly and easily with the knurled adjustment knob Also works with the speed wrench Instantly set your router to the approximate depth and then micro adjust

Use it in a router table or hold it by hand. Mounts to any router table and combined with your speed wrench makes height adjustments quickly and easily from above the table. Or, make handheld adjustments with the knurled adjustment knob that also works with the speed wrench. Plus, the quick adjust feature allows you to instantly set your router to the approximate depth and then micro-adjust. Fits the following routers: Fein RT-1800, Bosch 1619EVS, and Makita RF1101.

Most helpful customer reviews 1 of 2 people found the following review helpful. Grizzly has it cheaper By Henry J St.Pierre A great tool. Easy to install. Works better than advertised. Customer support couldn't be better. Grizzly has it on clearance for $47.00. 1 of 2 people found the following review helpful. Good decision By Joseph Yonke II Bought this several years ago. Works just like it says and just being able to adjust the depth of the router above the table. . .well, you won't be disappointed. Great price vs. the other versions available. See all 2 customer reviews...

Amazon Sales Rank: #17420 in Home Improvement Brand: Porter-Cable Model: 893PK Number of items: 1 Dimensions: 24.50" h x 8.63" w x 12.75" l, 21.50 pounds Soft-starting, 12 Amp motor features full-time electronic feedback that maintains motor speed through the toughest applications Variable-speed control feature (10,000 - 23,000 rpm) enables bit speed to be optimized for changing applications Plunge base features machined brass bushings and steel guide rods for a smooth, controlled plunge stroke Depth rod with 6-position adjustable turret enables stepped or repeated plunge cuts Dual-position switch allows user to cut power while maintaining control of the router

Fast, smooth, and efficient, the Porter-Cable 893PK gets its formidable strength from a 2-1/4 HP, super-quiet motor with superior electronic feedback and variable speed (10 - 23,000 RPM) to maintain consistent power and control. A built-in dust collection system helps improve visibility, while an easy-to-use knob makes it a snap to fine tune the height; there's also a bypass control to handle both large and coarse adjustments. The 893PK works with most 890 and 690 router series bases and also boasts machined brass post busing for durability. For added convenience, both the fixed and plunge bases lock or release instantly with a simple finger movement. Best of all, you don't have to crawl under the table and fiddle with screws to make adjustments--you can re-position right from the tabletop. The 893PK comes with a carrying case, transparent sub-base, 1/4-and 1/2-inch self-releasing collets, a wrench.

Most helpful customer reviews 36 of 40 people found the following review helpful. a waste of $250, buy a 690 series instead By J. Mangers I've been using PC products for 16 years and have loved every one of them until now. My last router was getting a little tired so I thought I would upgrade from a 690 to the new 893 and am appalled that PC put this unit on the market, it is a total waste of money. Here's what it comes down to: the motor itself is great, lots of power, smooth starting, and much quieter than the 690's, this is where the good review ends. The main problem I've found is that the bases are very poorly designed and constructed. It seems like PC was trying to add a bunch of new feautres to them and ended up sacrificing quality for nifty gadgetry. The new clear plastic base does not glide well over most of the woods that I use, instead it chatters causing rough choppy cuts. I tried waxing it, cleaning it with alcohol and even sanded it with 1200 grit paper and nothing seems to help with this problem. The bases are made from a very thin metal and do not seem like they will hold up well to the rigors of long term use. The plunge base has many problems including: depth adjustment/stop moves/comes out of adjustment when doing several of the same depth cuts in a row, the release lever seems to be desinged in a couter intuitive way and does not release in a consistent manner. The main guides that control up/down movement do not opperate smoothly and it's hard to tell if you've reached the stop or are just hung up in a sticky spot. I took this apart, cleaned it out and waxed everything and this did not solve the issue. The view on the measuring gauge is obscured by the tensioning knob for the gauge. All and all I thought these new features would work well and was looking forward to the next generation of PC routers and what I found is that if this is it, Porter Cable has sunk to or below the level of Ryobi. I see there are several good reviews here and not much critisism, do yourself a favor and look at the reviews for the PC 895PK before buying this router, it is the same unit with an added feature or two. Alas do not be too discouraged by this, the 690 series are still great products, what I would consider to be the industy standard, buy one of these instead and you'll get many years of trouble free use from it. Oh I almost forgot, I contacted PC customer support to see if there was any way to exchange this for a 690, they were unwilling to do anything and were not even the least bit apologetic about the issues I am having. Cheers! J. 15 of 15 people found the following review helpful. Actually Designed With the User in Mind By Ronald W. Owens I needed a router with a bit more Horsepower - my old 1-1/2HP machine was just getting worked too hard. I should mention that I already owned 3 routers - 2 at 1-1/2 HP, and a small "trimmer" type that I use a lot - more as a router than as a trimmer. I used one of the old routers in my router table, with an accessory variable speed control. I had already decided that a plunge base was in my future, because there were just times when nothing else was a better option. I decided to order the new Porter Cable 893PK, which, at 2-1/4 HP was a significant boost in horsepower. It included the plunge base at a better price than buying things separately. It has electronic variable speed, and a "soft start" feature that is wonderful - very little torque at start up. I was amazed at how much more quiet this machine is, than my old ones. Motors and mechanical things rotating at more than 20,000 rpm's tend to generate high frequency noise. Porter Cable has done a great job of minimizing the noise - the usual high pitched whine is gone. I mounted the fixed base to my router table and keep the plunge base for other jobs. Of course, I still own all the other routers, so there are options aplenty. I cannot say enough good things about the design of this tool. The depth adjustment in the fixed base